- 您现在的位置：买卖IC网 > Sheet目录372 > 101-1293 (Rabbit Semiconductor)RCM4510W DEV KIT
2.2.3 Step 3 — Connect Programming Cable
The programming cable connects the module to the PC running Dynamic C to download
programs and to monitor the module during debugging.
Connect the 10-pin connector of the programming cable labeled PROG to header J2 on
the RCM4510W as shown in Figure 5. Be sure to orient the marked (usually red) edge of
the cable towards pin 1 of the connector. (Do not use the DIAG connector, which is used
for a standard serial connection.)
1
Remove slot cover,
insert tab into slot
Assemble
AC Adapter
AC Adapter
2
Snap plug into place
3-pin
power connector
Programming
Cable
J1
U1
RESET
Colored
edge
C2
C1
UX47
BT1
UX49
1
UX4
S1
RESET
R3
C40
C8
C5
C46
R19
C41
U11
L1
C6
RCM1
C27
/RST_OUT
/IOWR
VBAT
EXT
PA1
J2
GND
/I ORD
/ RST_IN
PA0
PA2
+5 V
GND
+3.3 V
RX81
C16
C9
U3
R20
R14
C18
C4
JP16
JP6
JP5
JP12
JP4
JP3
JP14
JP8
C16 JP7
JP18
JP9
JP10
JP1
PA3
PA5
PA7
PB1
PB3
PB5
PA4
PA6
PB0
PB2
PB4
PB6
RX83
RX11
UX30
C15 C1
C20
U1 C21
C42 C22
Q8
Q1
C5
U17
C35
R25
C34
JP2
JP3
JP4
PB7
PC1
PC3
PC0
PC2
PC4
UX10
JP5
PC5
PC6
C44
RX43
C82
R65
C84
R29
R20
R10
R61
JP6
JP7
JP9
JP8
PC7
PE1
PE3
R19
PE5
R9
PE7
PD1
LN1
PE0
PE2
PE4
PE6
PD0
LN0
PD2
LN2
RX67
UX12
PD3
LN3
PD4
LN4
UX14
DS3
R22
RX97
RX49
RX55
RX57
RX59
R33
R31
R30
R35
R32
PD5
LN5
PD7
LN7
VREF
PD6
LN6
CVT
AGND
RX75
CX25
DS2
JP25
RX73
R23
CX27
CX23 RX77
R21
R24
RX79
UX16
UX3
R52
J3
1
1
GND
R51
S2
S3
GND
GND
Figure 5. Connect Programming Cable and Power Supply
NOTE: Never disconnect the programming cable by pulling on the ribbon cable.
Carefully pull on the connector to remove it from the header.
Connect the other end of the programming cable to an available USB port on your PC or
workstation.
Your PC should recognize the new USB hardware, and the LEDs in the shrink-wrapped
area of the USB programming cable will flash — if you get an error message, you will
have to install USB drivers. Drivers for Windows XP are available in the Dynamic C
Drivers\Rabbit USB Programming Cable\WinXP_2K folder — double-click
DPInst.exe to install the USB drivers. Drivers for other operating systems are available
online at www.ftdichip.com/Drivers/VCP.htm .
12
RabbitCore RCM4500W
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
101-8430-09-203
LED BASE SUBMINI PANEL INDICATOR
103-0537-403
CAP PMI OILTIGHT 1" CLEAR
103-1234-403
CAP LG PANEL IND BLUE OIL TIGHT
103-1336-403
CAP PMI TORPEDO 1" LIGHT YELLOW
103-3101-05-103
LED BASE T-3 1/4 PANEL OIL TIGHT
1032DX5
INDICATOR NEON GREEN PANEL MNT
1033QD5
NEON IND GRN LITE PANEL MNT QC
1034
LAMP INCAND S-8 DBL INDEX VOLT
相关代理商/技术参数
101-1294
功能描述:处理器配件 12VDC POWER SUPPLY REPLACES 101-0686 RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
101-1295
功能描述:处理器配件 RCM5600W Antenna Kit
RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
10-112989-1
制造商: 功能描述: 制造商:undefined 功能描述:
10112A WAF
制造商:Intersil Corporation 功能描述:
10112-A-0440-2
制造商:Amatom Electronic Hardware 功能描述:
10112-A-0632-2
制造商:Amatom Electronic Hardware 功能描述:
10112-B-0632-6A
制造商:Amatom Electronic Hardware 功能描述:
10-112-BLANK
制造商:Calrad Electronics 功能描述: